Skip to Content

Walksnail WS-M181 GPS Module

https://www.bzbuas.com/web/image/product.template/3480/image_1920?unique=455c2f4
The Walksnail WS-M181 GPS Module is a compact GNSS receiver and compass for FPV drones, RC aircraft, and other flying models. Built on the u-blox M10 platform's UBX-M10050 chipset with a built-in IST8310 magnetometer, it tracks up to 32 satellites across GPS, GLONASS, BDS, Galileo, SBAS, and QZSS, updating position up to 10 times per second. A protective ceramic antenna coating resists scratching and oxidation, and at just 18 x 18 x 4.6 mm and about 4.3 g, it fits almost any build without adding weight.
88.61 zł 88.61 PLN VAT Excluded
88.61 zł VAT Excluded
Price on request

    This combination does not exist.

    The Walksnail WS-M181 GPS Module Delivers Fast, Reliable Positioning

    The Walksnail WS-M181 GPS Module packs a full GNSS receiver and electronic compass into an 18 × 18 × 4.6 mm footprint weighing about 4.3 g, making it easy to fit into freestyle, cinematic, and long-range builds without adding meaningful weight. Built around the u-blox M10 platform's UBX-M10050 chipset, it works with GPS, GLONASS, BDS, Galileo, SBAS, and QZSS across six positioning-mode combinations, tracking up to 32 satellites at once across 72 search channels. An onboard IST8310 magnetometer supplies heading data alongside position, while a built-in backup battery keeps recent satellite data ready for a faster hot start the next time the aircraft powers on.

    Walksnail-WS-M181-GPS-Module-overview
    Walksnail-WS-M181-GPS-Module-multi-GNSS-chipset

    Six Satellite Systems for Reliable Positioning

    Working across GPS, GLONASS, BDS, Galileo, SBAS, and QZSS gives the flight controller more visible satellites to choose from than a single-constellation receiver, which shows up as a faster first fix and steadier positioning once airborne. 72 search channels and an output frequency of up to 10 Hz keep position data current during fast maneuvers, while a measured maximum of 32 tracked satellites leaves margin even in built-up areas or under partial sky obstruction.

    Walksnail-WS-M181-GPS-Module-ceramic-antenna-on-drone-frame

    A Ceramic Antenna Built to Survive Real-World Builds

    The module's ceramic antenna is finished with a sprayed protective coating that resists scratching and oxidation, so reception stays consistent even after it has been handled, mounted, and remounted between builds. At only about 4.3 g and 4.6 mm tall, it tucks onto a frame's top plate or canopy without disturbing the balance of a freestyle or cinematic quad.

    Walksnail-WS-M181-GPS-Module-built-in-compass

    Built-in IST8310 Compass for Accurate Heading

    An onboard IST8310 magnetometer works alongside the GNSS receiver as an electronic compass, giving the flight controller heading information that complements GPS position data — useful for navigation features such as Return-to-Home that depend on knowing which way the aircraft is actually facing.

    Walksnail-WS-M181-GPS-Module-built-in-backup-battery

    Built-in Backup Battery for Fast Hot Starts

    A built-in backup battery keeps recently acquired satellite data available between flights, so the module can perform a hot start and re-establish a position fix more quickly than starting from a cold search — useful for pilots who swap packs frequently between flights.

    Walksnail WS-M181 GPS Module Key Features

    6 GNSS Systems

    Built-in IST8310 Compass

    Fast Hot Start

    Compact 18 × 18 mm

    Frequently asked questions - Walksnail WS-M181 GPS Module

    Yes. Because it uses a new 10th-generation GPS chipset, it requires Betaflight 4.3.0 or newer. Flight controller firmware older than 4.29 only supports the NMEA protocol and will not read the module's full data.

    No. An IST8310 magnetometer is built into the module, so it provides both GNSS position and compass heading data over the same connection — no separate compass board is required.

    It connects through a JST-SH 1.0 mm 6-pin cable (included), broken out to TX, RX, GND, 5V, SCL, and SDA pads on the module itself for wiring directly to a flight controller's GPS/compass port.

    Walksnail WS-M181 GPS Module Dimensions

    Walksnail-WS-M181-GPS-Module-dimensions

    Walksnail WS-M181 GPS Module Specification

    Model

    Walksnail WS-M181GPS

    Chip

    u-blox M10 platform, UBX-M10050 GNSS chipset (10th generation)

    Frequency

    GPS L1, GLONASS L1, BDS B1, Galileo E1, SBAS L1, QZSS L1

    Positioning Modes

    6 combinations (default: GPS + GLONASS + BDS)

    Max. Tracked Satellites

    32 (measured)

    Power

    5V

    Size

    18mm x 18mm x 4.6mm

    Antenna

    Ceramic Antenna (Oil Spraying Process, Prevent Scratching and Oxidation)

    Receiving Channels

    72 Search Channels

    Compass

    IST8310

    Connector

    JST-SH 1.0mm 6-pin (TX, RX, GND, 5V, SCL, SDA)

    Baud Rate

    115200dps

    Output Protocol

    Dual-Protocol GNSS Output (NMEA Compatible)

    Output Frequency

    1Hz-10Hz (Default 10Hz)

    Speed Accuracy

    0.05m/s

    Horizontal Positioning Accuracy

    2D ACC1.5m (Open Air)

    Receiving Sensitivity

    Trace-162dBm;

    Capture -160dBm

    Weight

    Approx. 4.3g

    Max. Altitude

    50000m

    Max. Speed

    500m/s

    Max. Acceleration

    4G

    Operating Temperature

    -40℃ ~ +85℃

    Storage Temperature

    -40℃ ~ +105℃

    Walksnail WS-M181 GPS Module Package Includes

    • 1x Walksnail WS-M181 GPS Module
    • 1x JST-SH 1.0 mm 6-pin connection cable
    Walksnail-WS-M181-GPS-Module-kit-contents