VIFLY Beacon Wireless Buzzer
With the VIFLY Beacon Wireless Buzzer on board you fly with more peace of mind, because it notices a crash by itself and starts calling for you before you even take off your goggles. There is nothing to solder or connect, so you stick it on an FPV drone, a DJI drone or an RC airplane and keep flying. A loud signal and a light that flashes after dark make finding a downed drone in tall grass, bushes or at night much simpler.
VIFLY Beacon Wireless Buzzer — Sounds the Alarm on Its Own After a Crash
The VIFLY Beacon Wireless Buzzer is a drone locator with its own 80mAh LiPo battery that needs no soldering and no connection to the flight controller, so you simply attach it to an FPV drone, a DJI drone or an RC airplane. A built-in motion sensor detects a crash and starts a beeper of up to 105dB, and a light sensor turns on a flashing LED after dark. It measures 25x14x15mm, weighs 6g, keeps alarming for up to 30 hours and charges over micro USB in about 1.5 hours.
When the Alarm Goes Off
After a hard impact the beacon enters pre-alarm and whistles once every 3 seconds. If it detects movement within 30 seconds, for example when you pick the drone up and fly on, the pre-alarm is cancelled. If nothing moves for 30 seconds, it switches to the full alarm and beeps twice every 6 or 12 seconds. The alarm starts in three cases.
- The drone has crashed.
- The drone has been still for more than 5 minutes.
- The flight has lasted more than 40 minutes.
The sound changes over time to save the battery, as shown in the table below. If the drone lands in a dark place, the beacon keeps alarming without a night pause until the battery runs out.
First 30 seconds | Low volume |
30 seconds to 2 hours | Full volume every 6 seconds |
After 2 hours | Every 12 seconds or a pause until dawn |
VIFLY Beacon Wireless Buzzer Key Features
No Wires, No Soldering
The beacon has its own battery and does not connect to the drone electronics. You attach it to an FPV drone, a DJI drone or an RC airplane without soldering or changing any settings.
Automatic Alarm
The motion sensor detects a crash, and the alarm also starts when the drone has been still for more than 5 minutes. It works even when the main battery has been knocked out of the drone, because the beacon runs on its own power.
Loud Signal
The beeper reaches up to 105dB and sounds at full volume every 6 seconds for the first 2 hours. A loud signal is easier to hear when the drone is out of sight.
Night Light
A built-in light sensor detects darkness and turns on a flashing LED. After dark you can see the drone, not just hear it.
VIFLY Beacon Wireless Buzzer Layout
The parts are numbered as in the drawing from the manufacturer's manual.
- Micro USB port
- Button
- LED
- Buzzer
- LiPo battery
Hold the button for more than 1 second to switch the beacon on or off. When it turns on, it beeps twice and the green LED lights up; when it turns off, it beeps three times and the green LED goes out. The motion sensor sensitivity can be set to high, medium or low with the button while the micro USB cable is connected. When the battery is low, the green LED flashes quickly. During charging the red LED is on and goes out when the battery is full. The manufacturer recommends charging the beacon every 3 months so the battery is not over-discharged.
Frequently asked questions - VIFLY Beacon Wireless Buzzer
The VIFLY Beacon Wireless Buzzer needs no soldering and no connection to the drone electronics. Attach it firmly to the frame or body of the drone so that it does not shift, and leave the micro USB port and the button accessible for charging and switching it on.
Yes. The manufacturer designed it for DJI drones, FPV drones and RC airplanes. The beacon works independently of the drone electronics, because it has its own battery and motion sensor, and it weighs only 6g.
Up to 30 hours. For the first 2 hours it beeps at full volume every 6 seconds, then every 12 seconds or it pauses until dawn. In a dark place it keeps alarming without a night pause until the battery runs out.
In a typical flight the beacon stays quiet. The alarm starts in three cases: after a crash, when the drone has been still for more than 5 minutes, or when the flight has lasted more than 40 minutes.
Through the micro USB port, at 4.5-5.5V. Charging takes about 1.5 hours; the red LED goes out when the battery is full. A quickly flashing green LED means the battery is low. Charge the beacon at least every 3 months, even when you are not flying.
Yes. A built-in light sensor detects darkness and turns on a flashing LED, so you can see the drone as well as hear it. In the dark the beacon also keeps alarming without a night pause.
VIFLY Beacon Wireless Buzzer Specification
Model | VIFLY Beacon |
Type | Wireless self-powered buzzer |
Volume | Up to 105dB |
Battery | 80mAh LiPo |
Working Time | Up to 30 hours |
Standby Time | Up to 10 hours |
Charge Time | 1.5 hours |
Input Voltage | 4.5-5.5V |
Charging Port | Micro USB |
Sensors | Motion sensor, light sensor |
Motion Sensitivity | High / Medium / Low |
Light Signal | Flashing LED in darkness |
Weight | 6g |
Dimensions | 25x14x15mm |
VIFLY Beacon Wireless Buzzer Package Includes
- 1x VIFLY Beacon Wireless Buzzer